Heavy-duty channel system (MI)

MI

Hot-dip galvanized (HDG) installation girders with greater adjustability for heavy-duty applications

• Material composition: DD11 MOD – HN 555-4, S235JR – EN10025-2
• Surface finish: Hot-dip galvanized, 75µm - DIN EN ISO 1461

From $535.00

Compare (1)

MIC-C90-DH New

Hot-dip galvanized (HDG) bracket to concrete for heavy-duty applications

• Material composition: DD11 MOD - HN 547, S235JR - DIN EN 10025;Baseplate : ASTM A36
• Surface finish: HDG: min 75 µm - ASTM A123

From $315.00

Compare (1)

MIC-C120-DH New

Hot-dip galvanized (HDG) bracket to concrete for heavy-duty applications

• Material composition: DD11 MOD - HN 547, S235JR - DIN EN 10025, Baseplate : ASTM A36
• Surface finish: HDG: min 75 µm - ASTM A123

From $480.00

Compare (1)

MIC-S90H New

Hot-dip galvanized (HDG) bracket for heavy-duty fastenings to steel

• Material composition: DD11 MOD - HN 547, S235JR - DIN EN 10025, Baseplate : ASTM A36
• Surface finish: HDG: min 75 µm - ASTM A123

From $384.00

Compare (1)

MIC-S120H New

Hot-dip galvanized (HDG) bracket for heavy-duty fastenings to steel

• Material composition: DD11 MOD - HN 547, S235JR - DIN EN 10025, Baseplate : ASTM A36

From $455.00

Compare (1)

MIC-C-AA/-D

Hot-dip galvanized (HDG) baseplate for fastening MI-90 girders to concrete using two anchors

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

$251.00

Compare (1)

MIC-C-DH New

Hot-dip galvanized (HDG) baseplate for fastening MI-90 girders to concrete for heavy-duty applications

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector min 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $658.00

Compare (1)

MIC-C-UH New

Connector for fastening MI girders to concrete

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

$247.00

Compare (1)

MIC-CU-MAH New

Hot-dip galvanized (HDG) connector for fastening girders directly to concrete at angles between 0 and 180 degrees

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector min 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

$333.00

Compare (1)

MIB-CDH New

Hot-dip galvanized (HDG) baseplate for fastening MI girders to concrete

• Material composition: S235JR - DIN EN 10025-2
• Surface finish: HDG - EN ISO 1461

$660.00

Compare (1)

MIC-S

Connector (steel)

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

$348.00

Compare (1)

MIC-SH New

Hot-dip galvanized (HDG) baseplate for fastening MI-90 girders to steel for heavy-duty applications

• Material composition: Connector: S235 - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector min 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $514.00

Compare (1)

MIC-SH New

Hot-dip galvanized (HDG) baseplate for fastening MI-120 girders to concrete for heavy-duty applications

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector min 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $539.00

Compare (1)

MIB-SH New

Hot-dip galvanized (HDG) baseplate for fastening MI girders to steel

• Material composition: S235JR - DIN EN 10025-2
• Surface finish: HDG: min 55 µm - DIN EN ISO 1461

From $379.00

Compare (1)

MI-DGC

Hot-dip galvanized (HDG) double beam clamp for connecting MI girders to steel beams for heavy-duty applications

• Material composition: Clamp: EN-GJMB-350-10 - DIN EN 1562, EN-GJMB-450-6 - DIN EN 1562; U-bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Clamp 55 µm - DIN EN ISO 1461; U-bolt 48 µm - DIN EN ISO 10684; Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $282.00

Compare (1)

MI-SGC M16 New

Hot-dip galvanized (HDG) single beam clamp for connecting MI steel baseplates to steel beams

• Thread - M: M16
• Material composition: Clamp: EN-GJMB-350-10 - DIN EN 1562, EN-GJMW-400-5 - DIN EN 1562, EN-GJMB-450-6 - DIN EN 1562; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Clamp 55 µm - DIN EN ISO 1461; U-bolt, Nut 45 µm - DIN EN ISO 1461

$337.00

Compare (1)

MIC-SC

Hot-dip galvanized (HDG) connector used with MI baseplates that allow for free positioning of the girder

• Material composition: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2
• Surface finish: None (primer coating-basic connector)

$113.00

Compare (1)

MIC-E

Hot-dip galvanized (HDG) connector used to connect MI girders longitudinally for long spans in heavy-duty applications

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $352.00

Compare (1)

MIC-UH New

Standard hot-dip galvanized (HDG) connector for fastening MI girders to one another

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Backing plate: EN-GJMW-400-5 - DIN EN 1562, EN-GJMB-450-7 - DIN EN 1562; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Backing plate, Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $526.00

Compare (1)

MIC-BA /H New

Ultimate hot-dip galvanized (HDG) connectors offering highest versatility within the MI modular system

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Backing plate: EN-GJMW-400-5 - DIN EN 1562, EN-GJMB-450-7 - DIN EN 1562; Tooth Plate: S235 - EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector min 55 µm - DIN EN ISO 1461; Backing plate, Tooth plate, Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $388.00

Compare (1)

MIC-T

Hot-dip galvanized (HDG) connector for fastening MI girders perpendicularly to one another

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Tooth plate: S235 - EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Tooth plate, Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

$271.00

Compare (1)

MIC-L

Hot-dip galvanized (HDG) connector for fastening MI girders perpendicularly to one another

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Backing plate: EN-GJMW-400-5 - DIN EN 1562, EN-GJMB-450-7 - DIN EN 1562; Tooth plate: S235 - EN10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Backing plate, Tooth plate, Bolt, Nut 45 µm - DIN EN ISO 1461
• Set: Yes

$353.00

Compare (1)

MIC-90-LH New

Hot-dip galvanized (HDG) connector offering highest load capacity within the MI and MIQ modular system

• Material composition: S235JR - DIN EN 10025-2
• Surface finish: HDG: 55 µm - DIN EN ISO 1461
• Set: Yes

$498.00

Compare (1)

MIC-U-MA

Hot-dip galvanized (HDG) multi-angle connector used with MIC-MAH connectors for fastening MI girders to one another at an angle

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Tooth plate: S235 - EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Tooth plate, Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

$271.00

Compare (1)

MIC MAH New

Hot-dip galvanized (HDG) multi-angle connector for fastening MI girders to steel beams at an angle

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector min 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $558.00

Compare (1)

MIA-EC

Girder end cap for safer and neater covering of MI and MIQ girder ends

• Material composition: Moplen EP 240H
• Temperature resistance: -30 - 90 °C

From $89.25

Compare (1)

MIC-MI/MQ-X

Hot-dip galvanized (HDG) connector for fastening MQ strut channels parallel to MI girders

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector 55 µm - DIN EN ISO 1461; Bolt, Nut 40 µm - DIN EN ISO 10684
• Tightening torque: 37 ft-lbf

$568.00

Compare (1)

MIA-EH

Hot-dip galvanized (HDG) screw with an integrated toothed plate for easier fastening and one-handed adjustment of MI and MIQ connectors

• Material composition: Bolt: Steel grade 8.8; Tooth plate: S235 - EN 10025-2
• Surface finish: HDG: 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

From $110.00

Compare (1)

MIA-EH-P

Hot-dip galvanized (HDG) plate for easier fastening and one-handed adjustment of MI and MIQ connectors

• Material composition: Plate: EN-GJMW-400-5 - DIN EN 1562, EN-GJMB-450-7 - DIN EN 1562; Spring: EN 10270-3
• Surface finish: HDG: 45 µm - DIN EN ISO 1461

$133.00

Compare (1)

MIA-OH

Hot-dip galvanized (HDG) screw for easier fastening and one-handed adjustment of MI and MIQ connectors

• Material composition: Steel grade 8.8
• Surface finish: HDG: 45 µm - DIN EN ISO 10684
• Tightening torque: 62 ft-lbf

From $64.75

Compare (1)

MIA-TP

Hot-dip galvanized (HDG) tooth plate used with the MIA-OH bolt for fastening of MI and MIQ connectors

• Material composition: S235 - EN 10025-2
• Surface finish: HDG: 45 µm - DIN EN ISO 1461

$83.25

Compare (1)

M12-F-SL-WS 3/4"

Hot-dip galvanized (HDG) hexagon nut with self-locking mechanism used with all MI connectors

• Material composition: Steel grade 8
• Surface finish: HDG: 45 µm - DIN EN ISO 1461
• Tightening torque: 62 ft-lbf

$181.00

Compare (1)

MIC-PS/MIC-PSP

Hot-dip galvanized (HDG) connector for fastening pipe shoes to MI girders for heavy-duty applications with expansion

• Material composition: U-bolt: Steel grade 8.8; Plate: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Nut: Steel grade 8
• Surface finish: HDG: U-bolt, Nut 45 µm - DIN EN ISO 1461; Plate: 55 µm - DIN EN ISO 1461
• Tightening torque: 44 ft-lbf

$271.00

Compare (1)

MIC-TRC

Hot-dip galvanized (HDG) connector for fastening M12 (1/2") and M20 (3/4") threaded rods to MI girders

• Material composition: Connector, Square washer: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector, Square washer 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Tightening torque: 51 ft-lbf

From $86.75

Compare (1)

MIC-UB

Hot-dip galvanized (HDG) connector for fastening U-bolts to MI girders

• Material composition: Connector: DD11 MOD - HN 555-4, S235JR - DIN EN 10025-2; Washer: DIN EN ISO 7089; Bolt: Steel grade 8.8; Nut: Steel grade 8
• Surface finish: HDG: Connector, Square washer 55 µm - DIN EN ISO 1461; Bolt, Nut 45 µm - DIN EN ISO 1461
• Wrench size: 19 mm

From $211.00

Compare (1)

MIA-BO

Hot-dip galvanized (HDG) U-bolt for fastening pipe shoes to MI girders

• Material composition: U-bolt: Steel grade 8.8 - ISO 898-1; Nut: Steel grade 8
• Surface finish: HDG: 48 µm - DIN EN ISO 10684
• Tightening torque: 62 ft-lbf

From $286.00

Compare (1)

MIC-PG

Insert to reduce friction when fastening pipe shoes and U-bolts to MI girders

• Material composition: Plate: PE-UH MW; Anchor: PA
• Temperature resistance: -200 - 90 °C
• Coefficient of sliding friction: 0.15

$175.00

Compare (1)

Hot-dip galvanized (HDG) grade 8 hexagon nut corresponding to DIN 934

• Material composition: Steel grade 8
• Surface finish: Hot-dip galvanized - DIN EN ISO 10684
• Base material type: n/a

Error occurred

Please contact us.

Compare (1)